For the best reception possible in every state, you might consider a mobile scanner antenna which mounts magnetically to your car or truck. Pinch the sides of the antenna and attach it to the BCT Window Mount Antenna 1. Mount the antenna on the inside of the windshield at the far right-hand passenger side.
|Published (Last):||11 May 2011|
|PDF File Size:||19.96 Mb|
|ePub File Size:||17.61 Mb|
|Price:||Free* [*Free Regsitration Required]|
For the best reception possible in every state, you might consider a mobile scanner antenna which mounts magnetically to your car or truck. Pinch the sides of the antenna and attach it to the BCT Window Mount Antenna 1. Mount the antenna on the inside of the windshield at the far right-hand passenger side. Page 7: Mounting The Bct Caution: Be sure the cable is out of the way of anyone getting in or out of the car.
Snap the visor clip onto the BCT Page 8 Installation 2. Slide the clip over the front of the visor. Adjust the angle of the antenna as close to straight up or down as possible.
Note: You can remove and replace the BCT by sliding both the unit and the visor mount off and on the visor. Page 9 Windshield Mounting 1. Find a good position for the BCT on your windshield. Refer to the Helpful Tips on page 5 for some guidelines on mounting positions. Put the metal mounting bracket with the suction cups on the windshield to adjust it for best position. Page 10 Installation 4. Snap the windshield mounting clip onto the BCT Slide the plastic windshield mounting clip into the metal mounting bracket.
The mounting clip locks into the plastic portion at three different positions. These positions can be used for vehicles with different vertical angles of their windshields. Page 11 6. Place the bracket and the BCT in the proper location on the windshield of your vehicle and press the suction cups firmly against the windshield.
If the BCT does not fit flush against the windshield, try a different position on the metal mounting bracket. Operation of the unit on other voltages or polarities will cause damage to the unit and may create a fire hazard.
The straight power cord provided with the unit has bare wires at one end and a small connector at the other end. Run the power cord from the fuse box to the BCT Note: Ensure the cord does not interfere with vehicle operation or cause a tripping hazard. Page Replacing The Fuse Connecting the Power When installing the power cord, make sure that: The socket is clean to allow proper contact. The power cord does not block the antenna area of the unit. Your unit also comes with 10 power cord mounting clips.
You can use these clips to attach the power cord to the window frame or other parts of the vehicle, keeping it neat and out of the way.
During power-on, a self-test is performed. Check the front control panel for proper operation. Page 17 4. Sometimes when you open the Squelch, you may trigger the Alert feature even though no highway patrol cars are in the area. Then turn the BCT off, and back on, to reset the Alert feature. Note: In metropolitan areas, you may want to adjust the Squelch control more counterclockwise to reduce the range of the Alert feature. Select the state you are operating in by pressing the repeatedly.
If you press and hold the the selector moves rapidly through all the states and Canadian provinces. Mobile extender and other enforcement channels are priority checked for activity.
Page 21 Scanning Local Police Frequencies This mode scans only the local police and county sheriff frequencies. Mobile extenders and other enforcement channels of the Highway Patrol are priority checked for alarm activity. Note: The priority check can be turned off by pressing and holding the Alert key for two seconds. Page 22 Operating Instructions 1. To scan highway patrol and local police frequencies, press the key repeatedly until HL is blinking on the LED display.
While scanning, the BCT displays the state code for the state you selected. Page 23 2. Page 26 Operating Instructions Muting the Priority Alert While in the highway patrol mode you can turn off the alarm tone during the time you are listening to a frequency or disable the alarm tone permanently. To disable the alarm tone while listening to a frequency: 1. Page Weather Alert 2. Press the key to make the BCT scan for the next weather frequency.
Uniden BCT15 Owner's Manual
Page 10 Installation 4. Make sure the BCT is not scanning. Refer to the Helpful Tips on page 5 for some guidelines on mounting positions. To print the manual completely, please, download it.
Uniden BC860XLT Manuals & User Guides
Arazuru Snap the visor clip onto the BCT To reduce the risk of fire, electrical shock, or damage to the unit, do not expose this unit to rain or moisture. Refer to eBay Return policy for more details. During power-on, a self-test is performed. Run the power cord from the fuse box to the BCT Learn more — opens in a new window or tab.
Uniden BCT-12 Manuals
Taudal No additional import charges at delivery! Check the front control panel for proper operation. Operation of the unit on other voltages or polarities will cause damage to the unit and may create a fire hazard. Find a good position for the BCT on your windshield. Email to friends Share on Facebook — opens in a new window or tab Share on Twitter — opens in a new window or tab Share on Pinterest — opens in a new window bvt12 tab Add to watch list.
Uniden BCT15X Manuals
- EDWARD ALDWELL HARMONY AND VOICE LEADING PDF
- IEC 61970 PDF
- LEY 25019 PDF
- ENEAGRAMA DE LA SOCIEDAD CLAUDIO NARANJO PDF
- ARBAN PARA TUBA PDF
- AZO ITCH RELIEF COUPON PDF
- GAI EATON ISLAM AND THE DESTINY OF MAN PDF
- COURS SAP2000 FRANAIS PDF
- ELEMENTS OF ENGINEERING ELECTROMAGNETICS NANNAPANENI NARAYANA RAO PDF